Quality Engineered Automotive Racing Products and More
Datsun 240-260-280Z Suspension
Camber Plate Kits: Each kit contains (2) mounting plates, (2) sliders with 5/8 spherical bearings, (2) spring perches, (1) needle bearing kit and mounting hardware. The kits are made from black anodized aluminum. To use the spherical bearing, it may be necessary for you to turn down the shock shaft where it goes through the bearing in the slider. Please specify what shock you are using when ordering.
Part Number: 204-1003
Camber Plate Kit: Datsun 240/260/280Z centered slots, bolt-in installation, requires cutting of the strut tower.
Price: $305.00
Part Number: 204-1017
Camber Plate Kit: Datsun 240/260/280Z Street Prepared, front, biscuit type, no cutting of strut tower required.
Price: $265.00
Part Number: 204-9017
Camber Plate Kit: Datsun 240/260/280Z Street Prepared, rear, biscuit type, no cutting of strut tower required.
Price: $245.00
Part Number: 299-1015-1
299-1026 Labor to turn shocks to fit camber plate spherical bearing. Each
Price: $20.00/shock
Threaded Collars: We supply two types of threaded collars. One is machined aluminum and the other is nickel plated steel. The aluminum collars are 5" long by 2 1/8" ID and have two jam nuts which allow you to raise or lower the car. The collars are designed for a 2.5" ID coil-over spring. The collars are supplied with weld rings. The IT collar has one bottom weld ring and the standard collar has both top and bottom weld rings which holds the collar in place. The steel threaded collars do not require weld rings.
Part Number: 214-1100
Aluminum Threaded Collars: 2" dia. strut tube, 2.5 I.D. spring, aluminum with steel rings pressed into ends for welding to strut, 5" long.
Price: $135.00
Part Number: 214-1101
Aluminum Threaded Collars: 2" dia. strut tube, 2.5 I.D. spring, aluminum with a steel ring pressed into one end for welding to the strut, 5" long.
Price: $125.00
Part Number: 214-1225
Steel Threaded Collar: 2" diameter strut tube, 2.5" I.D. spring, 6" long.
Price: $150.00
Part Number: 214-1237
Steel Threaded Collar: Steel, 280Z. 2.18" diameter strut tube 2.5"I.D. spring, 5" Long x 2.18 ID.
Price: $165.00
Part Number: 210-1000
Spanner Wrench: Used to tighten or loosen our coil over nuts and perches
Price: $16.50
Part Number: 826-XXXXX
Coilover Springs: Hyperco 2.50" I.D.
.png)
Part Number: 825-XXXXX
Coilover Springs: QA! High Travel 2.50" I.D.
Part Number: 825-HSG250
Helper Spring Guide: Keeps helper spring indexed with main spring. 2.50" ID Spring.
Price: $25.50/each
NEW
NEW
Part Number: 825-HSG225
Helper Spring Guide: Keeps helper spring indexed with main spring. 2.25" ID Springs
Price: $25.50/each
Part Number: 825-HS250
Coilover Helper Spring: Hyperco Blue 2.50" I.D. x 4" Free Length Steel Helper Spring
Price: $40.00/each
NEW
Part Number: 820-8641-1035-SPORT
Sport Shock: KONI sport adjustable gas strut insert. For street use with shortened struts. Includes one insert and everything shown in the photo.
Price: $184.25/each
NEW
Part Number: 820-8610-1437RACE
Race Shock: KONI racing adjustable gas strut insert. For use in DPracing shortened strut housings. This Koni race strut offers externally adjustable rebound damping. The piston rod is designed to fit through a 5/8" camber plate bearing with the provided adapter bushing. Sold as a pair, with gland nuts (Not shown in the picture).
Price: $585.00/pair
NEW
Part Number: 299-1015
Labor to shorten struts and install collars. Per pair.
Collars must be purchased separately.
Price: $110.00
Part Number: 299-1015-1
Labor to remove perch and install collars. No strut shortening. Per pair.
Collars must be purchased separately.
Price: $80.00
Part Number: 224-1002
Front Control Arm Bushing Kit: This kit consists of steel bushings and sleeves that replace the old rubber bushings. Spherical bearing type for stock bolt. Housings should be tack welded in place after installation.
Price: $158.50
Part Number: 224-1234
Knuckle Risers: Aluminum These 3/4" spacers are used to correct the suspension geometry changes (bumpsteer) that occur in severely lowered cars for both street and race. The mount between the steering arm and the bottom of the strut. They do NOT raise the ride height. Bolts are included. pair
Price: $80.00
Part Number: 224-1201
Knuckle Risers: Aluminum These 1" spacers are used to correct the suspension geometry changes (bumpsteer) that occur in severely lowered cars for both street and race. The mount between the steering arm and the bottom of the strut. They do NOT raise the ride height. Bolts are included. pair
Price: $80.00
NEW
Part Number: 224-2025
T/C Rods: Datsun Z, adjustable, ball socket type, bolt in, includes all hardware. Pair. New Style
Core required.
Price: $195.00
NEW
Part Number: 224-1212
Steering Side Rods: These are adjustable tubular rods are intended to replace the stock tie rod ends. They have 5/8" Teflon lined rod ends. Incl. hardware.
Price: $225.00
Part Number: 284-1240
Racing Stabilizer Bar: Front, Adjustable, 1-1/8" Tubular. Includes tubular sway bar, standoffs, pillow blocks, links, brackets and hardware.
Price: $609.00
Part Number: 284-2245
Rear Swaybar: Datsun 240Z/260/280Z adjustable 5/8" diameter rear. Includes new rear hanger plates, endlinks, pillow blocks, control arm rails, and hardware. Rails need to be fitted and welded to rear control arm.
Price: $475.00
Part Number: 234-1002
Rear Diff Solid Mount Kit: For mustache bar with 2 3/8" OD, fits 510-610-240-260-280Z.
Price: $55.00
Part Number: 234-1003
Front Diff Solid Mount Kit: Fits Datsun 240-260-280Z
Price: $75.00
Part Number: 299-1240
Labor to reinforce and install rod-end to rear control arm. Includes rod ends mounted to rear control arm and diagonal reinforcement,as well as the hardware to attach the arm to the rear strut. Per arm. Note: does not include installation of the rear sway bar mount. Core required.
Price: $300.00
Part Number: 299-1011
Labor to install swaybar mount on rear control arm. Per arm. Does not include reinforcement.
Price: $85.00